GT23028 RFQs: Confirm the Table Tennis Top Fit

Nov 10, 2026 | Industry Trends

GT23028 RFQs: Confirm the Table Tennis Top Fit

What should the GT23028 quotation show about the table tennis top?
Ask the supplier for a marked view of the GT23028 table tennis panel on the quoted air hockey base. The view should identify the panel orientation, where its underside is intended to sit, and any parts that locate it. Keep the panel and base revisions together in the quotation so a later replacement request can refer to the same fit.
The GT23028 product listing identifies an air hockey table with a table tennis top and lists the top separately from the air hockey playfield. The official gallery shows the two surfaces separately. Use that evidence to identify the component in an inquiry and ask the supplier for a marked view of the fit on the unit it offers.
The catalogue view identifies the two surfaces. Request an annotated image of the actual panel and base in their seated position.
Mark the surfaces that meet
Request one view of the underside of the top and a second of the uncovered air hockey base. Ask the supplier to mark the intended points or edges of contact on both views. Include a close view at a corner so the buyer can tell the panel edge, the base trim and the supporting surface apart. Have the supplier identify which features on the photograph are relevant to the fit.
If the supplier uses a pad, stop or locating part, ask it to mark the part and give its reference. If the offered panel has no separate locating part, ask what defines its seated position. Leave that field open until the supplier provides an answer. A picture of the top held above the base shows their relationship but gives the buyer little evidence about the contact below it.
The two pieces are visible separately. Ask the supplier to mark their contact surfaces on the underside and the base.
Ask for orientation and clearance on the quoted base
Give the supplier a consistent reference end for the views, such as a marked goal end in the photograph. Ask it to show which end and face of the top correspond to that reference. If the panel can be seated in more than one orientation, ask which orientations the supplier approves for the exact revision being quoted.
Ask for a side view of the panel fully seated. If an edge, post fitting or other protruding part could make contact, ask the supplier to mark the intended gap or identify the reference surfaces it checks. Use the supplier’s stated endpoints and units if it provides a dimension. Keep the overall table size in a different field from any fit dimension for the panel.
Buying field
Requested supplier response
Base identity
Quote GT23028 and identify the base sample and revision shown.
Panel identity
Name the top reference and revision, including any locating parts that belong to it.
Orientation
Mark a common reference end on the top and base views.
Seated contact
Mark the intended contact surfaces and identify the corresponding points on both pieces.
Clearance
Show the edge and any relevant protruding features in a seated side view.
Replacement compatibility
State the exact panel and base revisions that the offer covers.
Keep a replacement panel tied to the right base
Ask whether a replacement panel can be quoted separately for the reviewed base. If the supplier offers one, ask it to use the same panel reference as the approved sample or give a written compatibility statement for the proposed alternative. If a part number stays the same after a panel change, have the supplier point to the revision that it can supply.
The multi-game table parts guide helps buyers request an inventory of pieces by game. Keep the fit record beside that inventory. A parts list can identify a panel in the carton, while the marked view tells the receiving team how to recognize the intended match between that panel and the base shown in the quote.
The lower view shows the panel edge near the base trim. Ask for a closer seated view with the approved reference points marked.
Record what the sample and quote actually confirm
Ask the supplier to use the same two physical pieces in the seated view and the close views. On review, record the sample identifiers and compare the visible contact locations with the marked reference. If an end or underside detail differs, mark it in a photograph and ask the supplier to reconcile it before approving a new quote revision.
Use the Ruiqing Leisure contact page to send the model number, any existing base reference and the fit fields that still need an answer. Ask the supplier to list the photos or drawings that apply to the offer and give each one an identifier. For a repeat order, attach the previous fit record so any panel or base change is visible in the reply.
Identify the table tennis panel and air hockey base separately.
Keep the orientation and seated contact views with the sample record.
Confirm which revisions a separately quoted replacement fits.
Buyer FAQ
Can the overall table dimensions identify the replacement panel?
Ask for the panel reference and a fit statement for the matching base revision. Overall size does not specify where the panel is meant to sit.
Can the catalogue photo tell me how the top locates?
It identifies the top and base visually. Ask for annotated views of the contact and any locating parts on the offered sample.
What if the model number stays the same after a change?
Ask the supplier to identify the revised piece, the base revisions it fits and which view supports its reply.
Should I assume replacement panels are offered separately?
Confirm the scope of supply with the supplier. Record any separately offered panel as a quote line tied to the specified base.
wholesale air hockey tablesB2B supplier sample record

Get a Free Quote

Fill in the form and we'll get back to you within 24 hours.